|
1) IMPORTANT CAUTIONS: For safe & efficient use, read the instruction manual carefully and follow manufacturer's instructions.
· Use only butane gas cartridge with low pressure (3~5 kg/cm2), do not use refilled, old, rusty or deformed fuel cartridge.
· Do not use fuel cartridge that expose in sun light or store at temperature above 40oC.
· Do not use appliance in windy place (Fig. 1).
· Place appliance on a stable and flat surface (Fig. 2).
· Do not use oversize pot with diameter of bottom > 24cm (Fig. 3).
  
Fig. 1 Fig. 2 Fig. 3
2) INSTALLING THE FUEL CARTRIDGE:
- Make sure the cartridge is not empty and follow article [1)] to use the appropriate fuel cartridge.
- Open the bomb cover, make sure the ignition knob in OFF position (Fig. 4).
- Put the fuel cartridge in the right position: locate the notch collar on top of fuel cartridge, align the notch collar with the fuel cartridge index arm (Fig. 5A & 5B).
- Press down the lock lever knob until it is in the LOCK position (Fig. 6) and close the bomb cover.
- When the fuel cartridge in right position, the appliance is ready to ignite.
   
Fig. 4 Fig. 5A Fig. 5B Fig. 6
**Attention: While installing the fuel cartridge, if you hear a hissing sound, take the cartridge out and reinstall. Do not ignite the appliance when the cartridge is not in the right position.
3) HOW TO IGNITE AND ADJUST THE FLAME:
- Turn the ignition knob to IGNITE position (Fig. 7) until you hear a "click", flame will ignite automatically.
- If there is no flame, turn the ignition knob to OFF position and repeat the ignition procedure.
- if there is no flame after 4-5 attempts à follow article [6)] to repair.
- Turn the ignition knob clockwise from HIGH to LOW to adjust the flame from strong to small (Fig. 8).
 
Fig. 7 Fig. 8
**Attention: After the first time ignition, the flame may not spread heat burner, after 10-15 seconds use or put the pot on the appliance, the flame is adjusted automatically and steady burn.
4) HOW TO TURN OFF FLAME & TAKE THE CARTRIDGE OUT:
- Turn the ignition knob to OFF position (Fig. 9).
- Lift up the lock lever knob to UNLOCK position to disengage the fuel cartridge from governor (Fig. 10).
- Open the bomb cover and remove the cartridge out of the appliance.
 
Fig. 9 Fig. 10
**Attention:
- When interrupting use, turn the ignition knob to OFF position and switch lever knob to UNLOCK position to extinguish the flame and disengage the cartridge out of the governor.
- After use, take the fuel cartridge out of the appliance.
5) HOW TO RESET THE SAFETY DEVICE: When using fuel cartridge with high pressure (normally refilled cartridge), safety device will automatically close, refuse fuel flow into the governor à no flame although ignite. Resolution:
- Follow article [4)] to take the cartridge out of appliance.
- Turn the ignition knob to HIGH position to release fuel out of governor (Fig. 11).
- Press the RESET knob (red color) until you hear a cloud click to set the governor on default setting (Fig. 12).
- Replace a new fuel cartridge with acceptable pressure and follow article [2)] to install.
 
Fig. 11 Fig. 12
**Attention: Do not change the frame of governor & other components of appliance in any situation.
6) TROUBLE SHOOTING: If fail to ignite the burner after 4-5 attempts à follow below steps:
- Check the fuel cartridge: If it is empty à Replace a new cartridge.
- If there is fuel in cartridge, a common problem is the pressure in cartridge is too high (especially with refilled cartridge), safety shut-off device closed automatically, refuse fuel into governor, see article [5)] to repair.
- If there is fuel in cartridge & the pressure is acceptable (brand-new cartridge) à Check the position of spark plug: the gap between the plug and the head burner is 3à4mm (Fig. 13).
Fig. 13
- If still can't ignite, contact the supplier agent, store.
**Attention: Do not change the frame of governor in any situation.
|
